Kbic-120 manual

The KB Electronics KBIC Controls PM, Shunt and AC/DC motors over a range of 1/100 - 3 HP with only a few models. All models can be used on a wide range of motor horsepower by inserting KBs exclusive Plug-In Horsepower Resistor. Speed range is 50:1 with load regulation of 1%. Features include Auto Inhibit, Voltage Following, MOV transient Machine Tools. Screening and Printing Equipment. KBIC DC motor speed control is designed for applications demanding performance, reliability and low cost. The patented Direct-Fed current limit circuit protects the motor and control against overloads by limiting the maximum level of output current. The KBIC-120 does have programmable start: Quote. Source: User Manual. Acceleration start (adjustable from 0.5 to 4. seconds) provides a smooth start each time the AC power is applied. So, give it a try. Also, the current sense resistor can be reduced a little, but then you may cause other problems. 9443 KB Electronics KBIC Signal Isolator Board (SI-5) 9833 KB Electronics Plug-In Horsepower Resistor, 1 Ohm. 9834 KB Electronics Plug-In Horsepower Resistor, 0.51 Ohms. 9835 KB Electronics Plug-In Horsepower Resistor, 0.35 Ohms. 9836 KB Electronics Plug-In Horsepower Resistor, 0.25 Ohms. 9837 KB Electronics Plug-In Horsepower Resistor, 0.18 Ohms. A friend bought a KBIC-120 controller to use with a treadmill motor on his lathe. He hooked it up per the manual, but it blows the AC fuse immediatly at turn on. Loud pop. I have the controller on my bench. I have checked his hook up and it was correct. He has the correct fuse, and correct power resistor for 1 hp motor. motor is a PM type. KBIC-120 By KB ELECTRONICS - Buy Or Repair At Radwell - Radwell.com radwell.com. electronics kb kbic manufactured radwell. KB Electronics KBIC-240DS User Manual | Page 4 / 28 | Also For: KBIC manualsdir.com. kbic 240d electronics kb. KB Electronics KBIC-120 DC Motor Control 9429 - Industrial Sensors indsencon.com. kbic 12095 NW 39th Street, Coral Springs, FL 33065-2516 (954) 346-4900 • FAX (954) 346-3377 Outside Florida Call TOLL FREE (800) 221-6570 kbelectronics.com 5K POT MAX MAX MIN ACCEL P3 P1 P2 I1 I2 IR CL * SHUNT MOTORS ONLY A F1 AND F2 ARE OPTIONAL FUSES BASIC KBIC CONNECTION ARM FIELD* F1 F2 AC LINE 50/60 Hz A- L1L2 F+ A+ U F- Created Date: 2/18/2004 1:01:14 PM KBIC ® SCR DC Motor Speed Controls Ultra Fast CL Circuit Prevents Demagnetization in PM Motors Installation and. BASIC KBIC ® Operation Manual * See SAFETY WARNING * See CE information on page 5. This Manual Covers Models KBIC-120, 125, 240, 225, 240D, 240DS Prueba - OK Reparado KBIC-125 (9433) DC Drives, Chassis. The KBIC-125 is an adjustable speed DC Drive. It will control motors between 1/100-3/4 HP (1.5 HP w/aux. Heat-sink) by inserting the proper Plug-in Horsepower Resistor. The KBIC-125 motor speed control is designed for 90 VDC PM and Shunt motors. Speed range is 50:1 with load regulation of 1%. The KBIC-120 is a 115 VAC rated 9 Amps RMS @ 45C. The control is designed for 90 VDC PM Shunt and AC/DC motors. It will control motors between 1/100-1/2 HP (1.0 HP w/aux. Heat sink) by inserting the proper Plug-in Horsepower Resistor. Speed range is 50:1 with load regulation of 1%. Features include Auto Inhibit? The KBIC-120 is a 115 VAC rated 9 Amps RMS @ 45C. The control is designed for 90 VDC PM Shunt and AC/DC motors. It will control motors between 1/100-1/2 HP (1.0 HP w/aux. Heat sink) by inserting the proper Plug-in Horsepower Resistor. Speed range is 50:1 with load regulation of 1%