7al msd wiring instructions

installation instructions msd ignition • 1490 henry brennan dr., el paso, texas 79936 • (915) 857-5200 • fax (915) 857-3344 magnetic pickup (not used) the 75611 can be used with 6al, 7al, and 8 msd ignitions as well as the mag control 8973 output input efi control note: when this connector is used with a 2-pin connection, the white wire MPS Racing INSTALLATION INSTRUCTIONS MSD IGNITION• msdignition.com • (915) 857-5200 • FAX (915) 857-3344 CYLINDER PROGRAMMING The Switch is programmed for 8-cylinder applications, however it can be used with 4 or 6-cylinder applications. Ensure that MSD View is installed on the PC prior to connecting the Power Grid Ignition Controller. INSTALLATION OF THE VIEW SOFTWARE 1. Insert the installation CD Rom into the CD drive, wait up to 30 seconds, the CD will auto run, IF THIS DOES NOT OCCUR: Locate and open the CD Drive. Double click on the Setup file. 2. 7AL-3 Ignition Control. The 7AL-3 allows you to make adjustments any time you want. It packs high voltage with four step retards, three rev limits and an rpm switch. All of the features are adjusted using plug-in modules including the 3-Step Rev Control and Multi-Step Retard. Click here to download the MSD-7330 7AL-3 Ignition Control instructions. ignition msd 6a control digital. Msd 7al 2 Wiring Diagram 7220 - MYNAMEISNIQUE mynameisnique.blogspot.com. msd 6al 7al troubleshooting. Msd 6a Wiring Diagram Gm Installation Instructions 15 M S D | MSD 6201 Digital 6A Ignition manualsdir.com. msd ignition 6a control digital. 56 Msd 6al 6420 - Wiring Diagram Harness MSD 7AL-3C-PN 7230 PDF MSD 7AL-3, PN 7230 The most complete drag racing ignition available! The 7AL-3 is based off the well proven 7AL-2. It features the same capacitive discharge multiple sparks plus offers 20% more primary voltage and an additional 35% more spark energy. Not only is the 7AL-3 packed with more power but it also features a host MPN: 7222. Description. Description. You'll recognize the 7AL-2 Plus Ignition Control, as its predecessor is the most popular ignition control used in drag racing. The "Plus" model updates the original 7AL-2 with improved internal components with an added a 2-Step Rev Control and diagnostic LED. The mounting pattern is the same as the 7AL COM (915) 857-5200 FAX (915) 857-3344 Installing an MSD 7AL-2 Plus or 7AL-2 Ignition Control The MSD 7AL-2 Plus, PN 7222, updates the original 7AL-2, PN 7220 with efficient internal components plus a 2-Step Rev Control and a useful diagnostic LED. The two terminal strips allow for easier wiring. NEW MSD 7AL-2 IGNITION CONTROL WITH BUILT-IN 2-STEP REV CONTROL,COMPATIBLE WITH 4-6-8 CYLINDER ENGINES. MSD Ignition 6201 6 Amp Ignition Control Box , Red Reduces weight, clutter, wiring issues and saves space. Read more. 5 people found this helpful. Helpful. Report abuse. DAUGHTER. 5.0 out of 5 stars MSD IGNITION CONTROL BOS. Reviewed in If triggering with the Magnetic Pickup: 1. Make sure the ignition switch is in the "Off" position. 2. Remove the coil wire from the distributor cap and set the terminal approximately 1/2" from ground. 3. Disconnect the MSD magnetic pickup wires from the distributor. 4. Turn the ignition to the "On" position. Do not crank the engine. 5.